Getting Familiar with Plumbing: A Must for Installing a Bathtub
Getting Familiar with Plumbing: A Must for Installing a Bathtub
Blog Article
We've noticed this great article involving Tools You Need to Install a New Bathtub directly below on the internet and reckoned it made good sense to share it with you over here.
Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate speedily; if you need to open a wall surface to eliminate the old bathtub and also position the brand-new bath tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need a helper to leave the old tub as well as embeded in the new one. Make sure you have actually qualified on your own for the task as well as fit attempting it. Rather than employing a service provider to take over a halfway-completed task, it is better to think about employing one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This write-up will certainly aid you mount a new tub in your washroom if you have already purchased a brand-new bathtub and also don't require to change the setup of your previous water system pipes.
Your devices and material list ought to make up the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly bothersome because of the restricted gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly come from the pipes. Once the supply pipelines have been removed, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before moving on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers are in area between the faucet and the sink. Protect the faucet in position with the manufacturer provided backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type needs to be linked to the tap ends initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Using the two wood boards under its feet, put the tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the level and readjusting the feet on the bath tub till the level reads degree.
To set up faucets, fit all-time low of the furthest versatile tap port to the suitable supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the water system as well as examine all joints and brand-new pipework for leaks and tighten them if needed. Load the bathtub and additionally inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it right into its final placement.
Preparing for the Setup
First of all, the sustaining structure provided with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last setting.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, triggering the water to penetrate the wall in between the bath and also the tiling, causing issues with wetness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can crack rather early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog post on Installing A Bathtub while browsing the web. Are you aware of another individual who is fascinated by the niche? Please feel free to share it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Professional plumbers, immediate response. Report this page